Recent content by ezveedub

That's the same header removal I posted for the 2080 Super here: https://forum.alphacool.com/threads/waterblock-for-gigabyte-rtx-2080-super-windforce-oc-8g.813/#post-6901

I have the 2080 Super Windforce and with the concern you posted, you can correct it by removing the stand offs on the plexi top. But the best way is simple. Remove the stock 3 screws for the Gigabyte backplate, remove the backplate and use slightly longer screws that came with the GPU block and...

The terminal seems to be covered with the name placard that you pluck off at the left side notch and then unscrew the terminal block off. I just wanted a name placard with 2080 Super or similar, but they don't make one, so I have to look at creating one instead for 2080 Super. As far as...

They only offered this when I asked: https://www.alphacool.com/search?sSearch=terminal Would love to change mine to 2080 Super or similar

I have a DDC 3.2 pump, which should be the same DDC-1T PWM. On my Asus Hero XXII mobo, if I set 60% to 100% PWM signal range for pump use, the pump will always run at full speed. After playing with the lower, middle and upper PWM signals in the bios. 0% to 55% signal gives control from 1200 RPMs...

GPU block works and looks great, but does seem more restrictive than I expected. I'm using this GPU block with two 360 radiators and EK CPU block with a D5 pump with a Alphacool flow indicator and cannot get all the air bubbles out of the blocks at 100% PWM signal with the D5 pump. There is...

GPU block was not purchased directly from Alphacool, but from PerformancePCs in the US. If replacement pads could be supplied through them or directly, then yes, as I had to find left over thermal pads to make this work.

Finally purchased the 2070 Super block and removed unused RGB 4 pin connector J603 and the blocks fits fine. Just need to correct the thermal pad thickness as in noted in the original 2070 Super thread.

I assembled my GPU block on my 2080 Super and had noticed the same issue with the VRMs. The thermal pads are too thin, on the VRMs and the inductors. The pads for the electrolytic caps are too thick. The supplied themal pads are 1.0mm for the power components. The inductors and VRMs need 1.5mm...

Hi Metropolis334, once last question. Are terminal block logo covers available to change out from the "2070 super" wording to one that says 2080 Super or Geforce RTX ? I know there's different wording on other GPU blocks that should fit with either of those words.

HI, finally pulled the cooler off the RTX2080 Super. Here is a picture of the PCB. Looks like the only thing not the same as the 2070 Super is the lerftover 4 pin connector for RGB, which this card doesn't use. If needed, I would desolder & remove if needed. Gv-N208SWF3OC-8GD

I will possibly have pictures of the PCB with the stock cooler removed in a few days. I'll post them at that time, but I did notice this PCB has the 4pin socket for RGB, but the cooler doesn't have RGB, just the wire connector for the fans only on the other side.

Just checked the website link and its now showing "Expected to be available in 4 - 5 weeks"......not sure if they sold them all out already.

I received email reply yesterday back from info@alphacool.com stating the Windforce 2080 Super PCB layout was the same as the Windforce 2070 Super and to use the new Eisbach Aurora block...

Is there a waterblock that fits this Gigabyte RTX 2080 Super? Part# Gv-N208SWF3OC-8GD, which I think is the same PCB layout as the RTX 2070 Super Windforce, with the no RGB header and round solid capacitors instead of the flat MLCC ones. I see there's a block for the Windforce 2070 Super...