Recent content by Liquete

  1. L

    Alder Lake - Temperatures

    Good evening, Eddy Thanks you for you reply. I will think about evaluating other options.
  2. L

    Alder Lake - Temperatures

    Good morning, Eddy Thanks for your answer. I understand the situation. another question, what do you think of this solution' https://www.caseking.de/en/thermal-grizzly-intel-12th-gen.-cpu-contact-frame-fsd8-036.html
  3. L

    Alder Lake - Temperatures

    Good night, I update the status I have done cleaned the CPU Water Block, and the temperatures has been improvement a lot. I hadn't cleaned it for a year and a half, I did change the liquid, but I forgot about the block and I thought it was OK to wait a bit longer. Temperatures in Cinebench...
  4. L

    Alder Lake - Temperatures

    I havent checked it, if the outlet hose gets very hot. I seems that the flow is correct, but i am not sure. I dont have any sensor to measure it. If the cooling fins in the CPU are clogged, what i should do? How i can fix it / check it?
  5. L

    Alder Lake - Temperatures

    I tried it, but it does not improve the contact, neither the temperatures. I am quite stuck with this issue.
  6. L

    Alder Lake - Temperatures

    thanks for your help Eddy ok, i will try it this afternoon and tomorrow i will tell you
  7. L

    Alder Lake - Temperatures

    Yes the connections are right I checked yesterday, because i dont know what/where is the error Reservoir OUT - to - LEFT XPX IN RIGHT XPX OUT - to - Radiator Radiator - to Reservoir IN I checked with this PDF https://www.alphacool.com/download/Blizzard.pdf
  8. L

    Alder Lake - Temperatures

    I add more information in case it is of use I have done the cinebench test (not without fear), to check if the temperatures are correct in extreme environments. The result was that in single core it gets to about 60ºC and stays there, but with the multi-core it jumps up to 90 - 100ºC easily...
  9. L

    Alder Lake - Temperatures

    Hello Thomas I answer your questions and add information No, i dont know the flow rate. Attached photo of the thermal paste. Seems that have a little more underneath and in the both sides, but seems that all zone have thermal paste. Setup 1x back fan Noctua 1x front fan (original NZXT...
  10. L

    Alder Lake - Temperatures

    Hello again I have already received the new backplate, installed it and tested it. Temperatures have improved, but there are still peaks, and at times they are not low enough. The truth is that the processor has almost no load and the temperatures oscillate quite a lot for what I was used to...
  11. L

    Tube not clear

    I'm sorry I didn't reply, I don't know why I didn't receive the notification. Yes, the tubes are clean because I changed them. The previous ones, after applying the distilled water, were free of residues but still discoloured.
  12. L

    Tube not clear

    sorry for not replying sooner but I had notifications disabled by mistake. the tubes are about 3 - 4 years old. I have used premixed clear from alphacool and ewbk. every year I have changed the fluid cleaning the system with distilled water, and it has improved somewhat. in the end I changed...
  13. L

    Tube not clear

    Good afternoon, I am maintenace the liquid cooling, and the tubes are not clear. It is as if some kind of algae or residue has been generated. How can I clean the system? What product do you recommend to clean it with? Thanks for your help. Best regards
  14. L

    Alder Lake - Temperatures

    it's OK I'll keep an eye out thanks for letting me know
  15. L

    Alder Lake - Temperatures

    Good morning, Thank you for responding so promptly. Is there anything that can be done to improve it? or is it a consequence of the LGA1700 design?
Top