Search results

I would advise against using other thermal pads. We put 7W/mk Ultra Soft pads on the graphics cards. These are extremely soft pads. Higher W/mk values do not always mean better. This is a common misconception. The resistance of the pads is just as important, it has to match the product or...

I'm sorry, but we no longer offer this for these coolers. Unfortunately, I can't help you with that. If the O-rings are not cracked, then they do not need to be replaced. I suspect that something is wrong with the assembly. Screws that were not tightened enough or seals that are not correctly...

No, you can only read out the rpm, you will be not able to controll the pump since this DDC pump is not a PWM Version. This pump isn't intended to be speed-controlled, as it's already a throttled version of the standard DDC pumps.

Ahh... you are talking about the 3-Pin Fan connector. That is only for reading out the rpm signal. You can also put it on a 4-Pin PWM Header. Sorry for the missunderstanding.

That small connector is for the aRGB LEDs (Digital RGB LEDs). Included in the package is an adapter that goes from this small 3-pin connector to the standard aRGB connector. This can be connected to the aRGB controller on all current motherboards. Your two Aquacomputer products are only for...

If there are specific updates, I will let you know. The 9070XT Nitro is indeed on the list. I can't say much about the 9070 cards, as we've only received very few of them. I'm also not sure if we will cover as many models there. The demand for non-XT coolers is very low.

As already mentioned, the coils do not require cooling. With air coolers, they are only there to stabilize and protect the cooler. The huge air cooler is heavy and needs the support surface. Coils are generally never covered by water coolers, as it is unnecessary.

Das hat nichts mit "richtigen" Wärmeleitpads zu tun, sondern damit, dass die Toleranzen der GPU Höhen bei Nvidia sehr hoch sind. Dazu kommen die Toleranzen bei den Bauteilhöhen wie vrms und Rams. Wenn hier die GPU die maximale Toelranz nach oben hin ausreizt und auch nicht selten die Vorgaben...

That can be done. Everyone does it a bit differently. Some use extensions and D-plugs, or simply connect it with tubes, although using tubes is not the easiest solution due to the tight spaces. Some switch out the terminal and use the flat terminal (item 12987) and then connect it only using...

We offer ES coolers with rear-facing ports and a 1-slot design, but not for the cards you mentioned. We only produce these types of coolers upon special request from industry clients with sufficient order quantities. In such cases, we can also make them available to the end customer market...

Have a look in the configurator, it has been entered since yesterday. But we don't take videos from infleunecers or other users on the net into account for compatibility, only what we can verify ourselves. Unfortunately, too many false claims have been made in the past.

Pure is in work, we have the GPU here in house. I do not expect the White to have a different PCB. That would be very surprising. So far, all OC, non-OC, and white variants have always been identical.

Please write an email to info@alphacool.com Dont forget to put a link to this threat inside, so the support team can see the pictures.

No, that’s not quite accurate. A distro plate is essentially the following: a regular reservoir with one IN and one OUT port. All additional ports are essentially just loops – nothing more. That means they are individual chambers with an IN and an OUT, where you have to go in and out again. You...

Since the AMD board partners – with the exception of ASRock – haven’t shown interest in providing us with PCB layout data, we’re currently reliant on obtaining the graphics cards ourselves or through customer submissions. As a result, we’re not yet able to confirm compatibility for the non-XT...

In the moment.... because of tons of requests, a few days. I know, that is stupid, and we have now brought in people from other departments to answer the queries. It's pretty crazy at the moment. But it's just getting better.

Confirmed and in work: Powercolor: RX 9070XT Hellound RX 9070XT Red Devil XFX RX 9070XT Mercury Asus RX 9070XT Prime RX 9070XT TUF Gigabyte RX 9070XT Aourus RX 9070XT Gaming Sapphire RX 9070XT Pure RX 9070XT Nitro+ And before you guys are asking.... we will make more cooler for more models.

Die Eisbaer Extrem wird nicht in das Gehäuse passen. Die ist alles andere als klein. Ich würde einen 240 oder 360mm Radiator im Deckel platzieren. Die Festplattenhalterung neben dem Netzteil würde ich rausnehmen und an den Radiatorrahmen, der an den weiteren HDD-Käfigen ist, dann einen AGB...

Those are just examples in the manual to help you get a better idea and orientation. In the end, it doesn't matter whether you connect a radiator, CPU, or GPU cooler — you can set it up however you like.

Morgen, Eine Wasserkühlung funktioniert eigentlich ganz einfach. Grob, brauchst du folgende Komponenten: CPU Kühler - Ist klar Radiator - Wie bei jeder AIO brauchst du auch bei einer Wasserkühlung ein Radiator. Die Ampere CPUs sind recht leicht zu kühlen. Wenn ich mich recht erinnere haben die...