Search results

  1. Eddy

    Was wollt ihr?

    Die sind nicht in Planung. Die Nachfrage in diesem Segment ist generell viel zu gering. Man merkt das immer wieder bei den GPU Generationen. In der Regel verkaufen sich nur Kühler für die beiden Top Modelle gut, alles darunter rentiert sich dann nicht mehr. Das galt schon für die RTX 2XXX Reihe...
  2. Eddy

    Alphacool 4090 Reference block compatibility

    A visual inspection is based on images. It is impossible to bring all graphics cards in all variants into the house to test them physically. We often get 3D data from the manufacturers on which we design coolers. Then it is physically tested by a printout of the 3D data of the PCB with a print...
  3. Eddy

    Qualitätssicherung mangelhaft!

    Ich schließe das hier mal, haben wir ja im Luxx Forum geklärt. Ansonsten PN an mich falls noch etwas sein sollte.
  4. Eddy

    Advice for Purchasing Watercooling Set for Gigabyte AORUS GV-R69XTAORUSX WB-16GD AMD Radeon RX 6900 XT

    I'm sorry I threw your plans out the window. But I just can't recommend this in good conscience. In the small case it will also be difficult with firn air supply to the radiator. We have already had some customers who have built up so similar with a 240mm radiator in similar cases and in the...
  5. Eddy

    Eisblock Aurora GPX-N Acryl Active Backplate 3090/3080 Reference (13038) - inlet port

    It doesn`t matter wich port you are using for IN and Out at the active backplate. You only have to consider the flow direction of a cooler if a jetplate is installed, which is not the case with the backplate. This is a simple flow-through cooler.
  6. Eddy

    Advice for Purchasing Watercooling Set for Gigabyte AORUS GV-R69XTAORUSX WB-16GD AMD Radeon RX 6900 XT

    You can do this basically the same way as explained in the other thread. BUT.... cooling an i-9900 and a 6900XT with only one 240mm radiator is brave. That's about 400W of waste heat you want to cool with a single 240mm radiator. That will only work with very high speed fans. This will be a...
  7. Eddy

    Eiswolf 2 AIO Parts

    Thick radiators only bring an advantage if you mount fans on both sides that run at least 1500rpm. Otherwise, the thick radiator makes no sense. Better would be an XT45 with fans on both sides. You can continue to use the connections and hoses. You do not need to buy new ones. But the conversion...
  8. Eddy

    Alphacool Eisbaer pro Aurora 240, pump not working?

    Did you tried another connector for the pump? If the pump still doesn't seem to run and you can't read RPM, replace the AIO. Then the pump indeed seems to have a defect. First step is to ask your dealer for an exchange. Unless you bought from us directly. Then please send a mail to...
  9. Eddy

    Combo aus Eisbaer 360 CPU + Eisblock Aurora Acetal + Eisbaer GPX Extension Set sinnvoll?

    Wärmeleitpads liegen beim Kühler bei. Der Rest passt auch. Die unterschiedliche Schlauchdicke ist nicht sonderlich relevant. Die Schnellverschlüsse sind miteinander kompatibel. Das ist das Hauptkriterium.
  10. Eddy

    NexXxoS XT45 Full Copper 40mm Dual radiator tubing

    If you want to take the 40mm radiators with the Barbe fittings, you need hoses with an inner diameter of 6mm. With this your hoses will not fit. Alternatively, you can also take the X-Flow variant with G1/4" thread. You can mount the appropriate connections for your hose.
  11. Eddy

    Neue Eiswolf 2 AiO für RTX 4080/4090 & RX 7900XT/XTX

    Nein, aktuell ist keine Eiswolf für die Red Devil geplant.
  12. Eddy

    Rust red radiator out of the box?

    This is not rust. We do not paint the fins completely or only lightly. The more paint on them, the worse the heat transfer. This is the solution for all our radiators. This is the bare copper that shows through.
  13. Eddy

    4090 ichill Frostbite

    I think the colleague has misunderstood the whole thing somewhat. Of course, the card should not throttle. The Hotsport temperatures are indeed quite high, but that can have various reasons. The cooler is not properly mounted or the pads or the thermal paste was not applied correctly or the...
  14. Eddy

    Question regarding Alphacool Apex pump

    This is not a crack, but intentional. This is a locking ring that is put on at the end for safety. It must be open on one side, otherwise it would no longer be possible to get it over the hub. You don't have to worry about that.
  15. Eddy

    4090 ichill Frostbite

    @darket69 We deliver the coolers to Inno3D, Inno3D does the assembly itself. I suspect that something was not done correctly here when mounting the cooler, but you would have to contact Inno3D directly. We can only make assumptions. I can imagine that the pads are not properly placed on the...
  16. Eddy

    Eiswolf 2 TUF 3080/3090 - hoses in front or back

    Where the hoses are located makes no difference. They do not have to be in any air flow. The only important thing is that the radiator gets enough fresh air.
  17. Eddy

    Custom Loop Hyte Y60 / i9 13900KF / 7900XT-X Taichi

    Genau, es geht um den Core 1. Nein, noch sind wir nicht beim Worst Case... aber das kann immer noch passieren. Daher werde ich keinen finalen Termin nennen bis dieser sicher ist. Ich will bei dem Kühler zumindest eine gewisse Menge an Ware auf Lager haben, bevor wir in den Verkauf gehen.
  18. Eddy

    How many times to flush, how much dirt is acceptable?

    The vinegar attacks the copper. This also partially dissolves the soldering which is not made of copper. You can now rinse as often as you want, something will always come out. Good... at some point nothing more will come out, then when all the vinegar is out. But everything that has now been...
  19. Eddy

    How many times to flush, how much dirt is acceptable?

    There are so many guides on the Internet that are simply wrong. Just because a manufacturer's product is used as an example does not mean that the manufacturer was involved or knew about the guide. Therefore, all videos, forum posts and user guides should only be followed if they were explicitly...
Top